Premixed metal fibre burners based on a Pd catalyst

As an alternative to previously developed catalytic FeCrAlloy fibre mat burners based on perovskite catalysts, new catalytic burners have been developed based on Pd catalyst on lantana-stabilised Al₂O₃ and different fibre structures (NIT100A, NIT100S and NIT200S by ACOTECH NV). All development steps are considered, shifting from catalyst preparation (based on combustion synthesis of γ-Al₂O₃) to the optimisation of lantana and Pd loadings, from the definitions of the best catalyst-deposition conditions (washcoating) to the catalytic burners performances, determined in an ad hoc developed combustion chamber. The results show almost half pollutants emissions and better performance compared to various non-catalytic counterparts, especially as far as CO and NO_x emissions are concerned. Some flame instability problems were though registered, especially for one of the catalytic burner mattresses employed, at low specific power inputs and excesses of air (<375 kW/m² and <12%, respectively). Further, PdO/Pd transition is shown to influence the dynamic behaviour of the catalytic burners.     

Complete oxidation of methane at low temperature over Pt and Pd catalysts for the abatement of lean-burn natural gas fuelled vehicles emissions: influence of water and sulphur containing compounds

The catalytic activity of fresh Pd and Pt catalysts supported on γ-alumina in the complete oxidation of CH₄ traces under lean-burn conditions was studied in the presence or the absence of water or H₂S. Steam-aged catalysts were also studied in order to simulate long-term ageing in real lean-burn natural gas fuelled vehicles (NGVs) exhaust conditions. Without water or H₂S added to the feed, Pd catalysts exhibit a superior catalytic activity in methane oxidation compared to Pt ones, whatever the catalysts were fresh or aged. The addition of 10 vol.% water vapour to the feed strongly affects the activity of the fresh Pd catalyst, thus being only slightly more efficient than the fresh Pt one. H₂S has a strong poisoning effect on the catalytic activity of Pd catalysts, while Pt catalysts are more resistant. The fresh H₂S-poisoned Pd/Al₂O₃ catalyst was studied by TPD in O₂/He. Poisoning species decompose above 873 K as SO₂ and O₂ in relative concentrations consistent with the decomposition of surface sulphate species. However, a treatment in O₂/He at temperatures as high as 923 K does not allow the complete regeneration of the catalytic activity of H₂S-poisoned Pd/Al₂O₃. A mechanism involving the poisoning of PdO by sulphate species is proposed. Different diffusion processes by which these sulphate species can migrate back and forth between PdO and the support, depending on the experimental conditions, are suggested.     

定向凝固Al/C复合材料研究

本文首次进行了Al/C(SiC)复合材料定向凝固,研究了复合材料定向凝固过程以及组织形态与凝固速率的关系,获得了纤维束间胞晶和不同间距的树枝晶,发现非润湿系统复合材料定向凝固后性能降低,文中对其机制进行了探讨.     

稀土Pr对Al2O3-SiO2(Sf)/ZL109复合材料组织及性能的影响

本文采用挤压浸渗法 ,制得不同稀土含量的硅酸铝短纤维增强铝基复合材料。用光学显微镜观察了复合材料的铸造显微组织 ,分析了稀土含量对共晶硅组织形态的影响 ;用扫描电镜对复合材料基体中的稀土相进行了观察 ,探索了稀土相的分布位置及其形态 ;并对不同稀土含量的复合材料进行了摩擦磨损实验 ,结果表明稀土能增强复合材料的耐磨性     

生物工程发酵饮料—醋酸饮料

本文着重介绍醛酸饮料的形成、特点和营养保健作用。     

ERD facility for analysis of hydrogen and deuterium in solids

Hydrogen is the lightest element in nature, and so, its detection and quantitative analysis is difficult by the conventional methods utilized for other elements. In the recent years the technique of elastic recoil detection analysis (ERD) using 1–2 MeV He⁺ beam has been developed to quantitatively and simultaneously analyze hydrogen and its isotopes in solids. Such a facility has been set up using the 2 MeV Van-de-Graaff accelerator at IIT Kanpur. It facilitates H and D analysis in a material up to a depth of ∼ 1μm with a detection sensitivity of 0·1 at.% and depth resolution of about 300 ?. The application potential of this setup is illustrated by presenting the results of measurements performed on Al:H:D systems prepared by plasma source ion implantation and highT _c YBCO pellets exposed to humid atmosphere.     

氧化铝丝的研制

氧化铅丝生产过程中最关键的工艺是连续阳极氧化。氧化膜击穿电压决定于氧化膜厚度。控制膜厚度的三要素为:电解液(成份、浓度及温度),槽电压和铝丝走速。     

Al(OH)3对硅橡胶性能的影响

综述了Al（OH)3粒径和用量对硅椽胶漏电电流、脉冲电流、耐漏电起痕、表面粗糙程度、电蚀损、介电性能、拉伸强度及漏电电流实验重复性的影响。     

定量电子晶体学硼对Ni3Al的电荷密度分布的影响

阐述了定量电子晶体学测定晶体电荷密度分布的基本原理和方法，不足之处和改善途径。以硼对Ｎｉ３Ａｌ的电荷密度分布的影响为实例，介绍了定量电子晶体学在研究晶体电子结构方面的应用前景。     

准连续Ti~(3+):Al_2O_3可调谐激光的研究

本文给出了Ti~(3+):Al_2O_3的准连续可调谐激光的实验结果。采用Nd:YAG内腔倍频532nm的准连续输出作为泵浦源,得到Ti~(3+):Al_2O_3的连续可调谐输出。波长覆盖范围为685nm到821nm。最大输出功率为293mW,斜率效率为20％,在805nm处的窄谱输出功率达240mW,总体转换效举为26％。